製品ニュース

1. Vertical black lines of more than 1 cm in width appear on both the printed document and the drum core: This is a problem with the scraper, which causes the powder on the stick core to not be scraped cleanly. 2. Vertical thin black lines appear on the printed document: Usually the scraper and the small scraper on the edge of the scraper are stuck with dirt or paper scraps. 3. Horizontal black lines appear on the printed document: Usually the magnetic stick in the toner cartridge has accumulated powder, just turn it a few times. 4. If there is obvious bottom ash on the printed document: Usually there […]

From the cost point of view, the cost of adding toner to the toner cartridge is much lower than that of replacing the toner cartridge, so adding toner is more cost-effective. However, from the actual use, since the toner cartridge is a sealed disposable consumable, adding toner by yourself will destroy the sealing performance of the toner cartridge and cause toner leakage. Therefore, the toner cartridge cannot be added too many times. Under normal circumstances, the toner cartridge can be added about 2-3 times (different toner cartridges also have differences) In summary, when the printer toner is used up, you can add toner 2-3 times and then replace the toner […]

1. First turn off the printer power switch, unplug the printer from the power outlet. 2. Then open the flip cover of the laser printer, carefully remove the photoconductor assembly, wipe its surface with a degreasing cotton, but can not force, in order to prevent the surface of the photoconductor scratched. 3. Next, wipe the surface of the photoconductor drum with degreasing cotton dipped in a special photoconductor cleaner. When wiping should take a spiral drawing circle type method, wipe brightly immediately after the degreasing cotton to wipe the cleaner. 4. After wiping the surface of the drum with talcum powder containing gauze gently pat a layer of talcum powder […]

1. Do not place heavy objects on the copier. 2. Be careful not to let paper scraps, staples or other small metal objects fall into the copier. 3. Do not try to remove any fixed plates or covers while the copier is running, and do not turn off the power switch. 4. When making large quantities of copies continuously, ensure good ventilation. 5. Do not allow any magnetic objects to approach the copier. 6. Do not place vases or water containers on the copier. 7. Make sure to turn off the power switch after work every day or when the power is interrupted.

1. High density. The minimum printing resolution of laser printers is 300dpi, and there are also high resolutions such as 400dpi, 600dpi, 800dpi, 1200dpi, 2400dpi and 4800dpi. 2. High speed. The minimum printing speed of laser printers is 4ppm, generally 12ppm, 16ppm, and some laser printers can reach a printing speed of more than 24ppm. 3. Low noise. Generally below 53dB, very suitable for use in quiet office spaces. 4. Strong processing power. The controller of the laser printer has a CPU and memory. The controller is equivalent to the motherboard of the computer, so it can perform complex text processing, image processing, and graphics processing, which cannot be done […]

1. When removing the "paper jam", only move the parts that are allowed to move in the copier manual. 2. Take out the whole paper at once as much as possible, and be careful not to leave broken pieces of paper in the machine. 3. Do not touch the photosensitive drum to avoid scratching the drum. 4. If you are sure that all "paper jams" have been cleared, but the "paper jam" signal still does not disappear, you can close the front cover again, or turn the machine power on and off.

1. Paper runs out When the paper runs out, the panel will show an empty paper tray signal, and you can load copy paper. You can continue copying. 2. Insufficient toner When the toner is insufficient signal light is on, it means that the toner in the machine is almost used up, which will affect the copy quality. It should be replenished in time. Some models will stop running when this signal appears, and some models can continue to copy. Before adding toner, the toner bottle or cylinder should be shaken several times to crush the agglomerated toner into powder. 3. Too much waste toner The waste toner removed from […]